,lexia 3,ca n clip
get obd2 diagnostic tools - diyobd2.fr,lexia 3,ca n clip
get obd2 diagnostic tools - diyobd2.frRenault CAN CLiP no vcc 3.3v to AN2135SC
In the CAN CLIP inner board, I found no vcc 3.3v to AN2135SC fromvoltage regulator. Actually there is no +5v IN from usb port to voltage regulator . Need +5v on both pins (1 and 3)
On red arrow no +5V on image,normally no 3v3 to blue arrow,but on green there is +5v
Also from back side near usb connis also same vol.reg and its have all voltages ok
Here are some Renault clip users’ solution. I adopted it... Worked!
it is possible solder a wire from +5v to IN pin, but also need to OFF\ON pin to enable output voltage 3.3v. But in that case both red diodes are ON even no connected obd conn to car. Also tried to "take" 3.3v from other clip pcb and then find sonde when start clip sq, only ask for firmware update so will try lower version sw. Now use v96
Then I sill bring +5v to both IN and ON/OFF and will get 3v3 only both red leds will be on
Another user also had a problem with the 3.3V regulator , and he used a normal 3.3v regulator without ON/OFF and it worked correctly , except that the 2 red leds always on.
Original - from diyobd2.fr obd2 francais:Renault CAN CLiP no vcc 3.3v to AN2135SC (customer solution)
OBDSTAR X300 DP adjust mileage for 2016 Cadillac ATS-L
This blog will show you how use OBDSTAR X300 DP tablet adjust mileage tool to change and adjust mileage for a 2016 Cadillac ATS-L. Steps are as below:
The original odometer is 9061KM
Connect OBDSTAR X300 DP with car. Power it on and choose “GM”.
Choose “GM V30.45”, select “Cadillac” then “ATS2013-”.
Choose “Mileage adjustment” and it will read out the original mileage as 9060KM, confirm that to continue.
Enter the new mileage 3061
Click “YES” to confirm and the mileage immediately changed from 9061 to 3061!
Now OBDSTAR X300 DP adjust mileage for 2016 Cadillac ATS-L successfully! The above procedure is simple to operate and easy to understand!
Original - from diyobd2.fr obd2 francais obdstar x300m:New arrival OBDSTAR X300 DP adjust mileage for 2016 Cadillac ATS-L
I-2015 Actia Multi diag works no issues on BMW E90, bmw mini
Something interesting on multi diag access j2534 interface. share it here. Maybe helpful to you.
First I used Muti diag software on a BMW MINI 2011. One client took his car to my garage because the airbag light constantly flashed. I tested it with VCI but no code stored. I checked some other parameters and all fine. Then I disconnected the battery, and did a battery reset for half an hour. The SRS light went off finally.
Then I run muti-diag access on BMW E90. Read and cleared fault codes of engine injection mevd17kw n55. Lots of sreenshots i took this time, for share. It will better to help all know Muti-diag.
OBDSTAR X300M Odometer Correction Tool change Audi Q5 mileage easily
This is guide for using OBDSTAR X300M Odometer Correction Tool to change mileage for Audi Q5 2010. The operation is easy and clear as follows.
The original mileage: 22850 KM
Step1. Connect OBDSTAR X300M to car and start the device. Choose “Vehicle”→ “AUDI/VW/SKODA/SEAT”→ “Audi”→ “Q5”→ “2008-2012”→ “Mileage Adjustment”.
Step2. Now OBDSTAR X300M will show the exact original kilometer. Press the Enter button to continue.
Input new mileage kilometer you want to change, in this car it is “105312”. Press the Enter button to confirm.
It will start to adjust odometer, usually 10-25 minutes to wait.
After that adjustment complete.
Things done! OBDSTAR X300M Odometer Adjustment Tool successfully change Audi Q7 mileage from 22850 KM to 105312 KM!
Flyobd FVDI2 Renault Abrites Test Report of Key Programming
Test reports here of Fly obd terminator FVDI 2 Renault to read pincode and program keys... Big thanks to all fvdi2 users.
Flyobd FVDI2 success on Renault:
- Brand/Model of car : Renault Scenic 2 - Year of car : 2004
- Feature in relation : Key Learning (keycard pcf 7947)
- Version of FVDI : 5.2
- Result : Ok
- Brand/Model of car : Renault Scenic II ph2 1.5 dci- Year of car : 2009
- Feature in relation : learning key
- Version of FVDI : 5.2
- Result :ok
- Brand/Model of car : Renault Clio 2- Year of car : 2010
- Feature in relation : Key learning
- Version of FVDI : 5.2
- Result : Ok
- Brand/Model of car : Renault Kangoo DCi 1.5 ecu Delphi TRW DDCR 1.5 DCi- Year of car : 2005
- Feature in relation : Transponder learning 7936
- Version of FVDI : 5.2
- Result : ok
- Brand/Model of car : Renault clio classic petrol- Year of car : 2004
- Feature in relation : reading pin
- Version of FVDI : 5.2
- Result : Ok
- Brand/Model of car : Renault Megane 3- Year of car : 2013
- Feature in relation : tacho correction
- Version of FVDI : 5.04
- Result : OK
- Brand/Model of car : Renault Megane 2- Year of car : 2008
- Feature in relation : Dash Km
- Version of FVDI : 5.2
- Result : Ok
- Brand/Model of car : Renault Espace- Year of car : 2006
- Feature in relation : pin read and key programming
- Version of FVDI : Renault 6.3
- Result : OK
- Brand/Model of car : Renault Grand Scenic- Year of car : 2005
- Feature in relation : pin read and key programming
- Version of FVDI : Renault 6.3
- Result : OK
- Brand/Model of car : Renault Traffic
- Year of car : 2004
- Feature in relation : pin read and key programming from UCH dump
- Version of FVDI : Tagkey Tool 6.2
- Result : OK
Fvdi 2 failed on Renault:
- Brand/Model of car : Renault symbol 1.2- Year of car : 2011
- Feature in relation : read pin
- Version of FVDI : 5.2
- Result : not ok
(the test report is updating...)
Attachment:
relate product: