Have got the alliance vi to work with Consult3 plus software. And make Consult III+ to run it with Ford VCM II interface.
CarDaq
Actica Passthru+ XS
Python1B
Nissan USB Diag
Alliance VI
And The obvious tool VI2
all these are the best to work with Consult 3 plus.
others will also work but maybe not as well.
The Ignition ON its not seen if you use VCM II
I use AVDI and Ignition ON it is not seen too
I read that no matter what j2534 tool you use the Ignition ON its not seen
Probably, only if use Alliance VI2, but alliance vi is quite a bit more complicated to set up
Here is thesetup of VCM II with Nissan Consult 3+.
For ford VCMII
In the Diagnostictool.ini put Ford-VCM-II
Install the consult 3 plus
Install your VCMII Manager and drivers.
In passthru 4.04 in reg edit and rename NISSAN_VI2 To something else
change name Bosch Ford-VCM-II to NISSAN_VI2
Reboot computer and test it
I tested it once with limited success.
Attachment: [Diagnostictool.ini]
Note 1: [alliance vi]
The sonde alliance vi is the end for the sonde can clip RTL. remplaced by sonde alliance vi but what is it.
Renault Aliance VCI = 100% Same with Nissan Consult III VCI...
Just & ONLY different name...
Note 2: [workable sw]Clone Consult III (who using patch) for to working with Nissan Consult III S/W, DID NOT working with Clip Software!!!
It seems now Clip S/W needs NEW "Pill" for Clones..
I’ve been trying to get Consult 3 plus V46.11.00 to work with my NEXIQ usb link. Nexiq supports J2534 so i figured I would give it a shot. I have a CF-19 Tough book which contains all me software for diagnostic. The CF-19 runs in deep freeze all the time to prevent any issues. So I typically test software I acquire on my desktop first. Long story short I installed it on my Desktop edited the .ini file and got it to show connection to my nexiq. (Haven’t tested on a car because my desktop is in my living room). So I thought I was good even wrote a short tutorial to keep with my backups of software. I then installed on the CF-19. Edited the .ini. Expected to the the USB connection with the blue dot.... Nothing. I installed both exactly the same. Im running identical versions Windows 7. There is quite a bit of software on my CF-19 I don't if its interfering or not. Does anyone have any ideas. To be so close to it working but not able to test is frustrating. Below I will put my short tutorial to show the steps I took and also maybe it will help others. (This is not my work just the steps I found on here)
J2534 PassThru for Nissan Consult 3 plus
1. Install Niassan Consult III+.
2. Make sure the driver for your PassThru is installed.
3. Open regedit.exe
4. Navigate to HKEY_LOCAL_MACHINE > SOFTWARE > Wow6432Node > PassThruSupport.04.04
5. From there choose your device. (For example I have a Nexiq Usb-link, so I choose either " NEXIQ Technologies - USB-Link" or "NEXIQ Technologies - USB-Link Bluetooth". I choose to use standard USB-Link)
6. Once you've click on your device look in the right column for "Name"
7.Right click on "Name" and choose "Modify..."
8. A window will appear copy exactly what it say in the "Value data:" box. (For example mine is "NEXIQ USB-Link over USB")
9.Close regedit.
10. Naviagte to "C:\CONSULT-III_plus\System\Application\ApplicationData\CommonSetting"
11. Open "DiagnosticTool.ini"
12. Copy & Paste the text below under "access_mode=1" in DiagnosticTool.ini
with the exeption of putting the text you copied from regedit in place of "!!!!YOUR_DEVICE_NAME!!!!":
[device]
vi_device_name=!!!!YOUR_DEVICE_NAME!!!!
[mode]
debug_mode=TRUE
debug_mode_vehicle_battery=TRUE"
13. Done
Ps. special thanks to the one share tips above at http://mhhauto.com/